SKU
IH45AB

45KW Mid-Frequency Split Induction Heater w/ Timers 30-80KHz

Price $11,990.00

CUSTOMIZE YOUR PRODUCT

Wishlist

Product Video

Videos

Note: This model only available in 460-480 volt three phase.

Across International IH series mid-frequency induction heaters are designed to operate between 30 and 80 kHz. Mid-frequency heaters are excellent for small parts heating, cutting, diamond tool brazing, soldering copper plumbing fittings, auto parts heat-treating, annealing of stainless steel containers and more.

Mid-frequency induction heaters are the simplest in terms of design and implementation. With their low cost of ownership and maintenance, they are the most popular and reliable machines. The 15kW models are especially popular for their large power capacity and small footprint at an affordable price. This makes them standard equipment for many factories, labs and workshops where 230V AC is available.

 

Safety Features

  • Overvoltage protection: machine shuts down when input voltage is over 245V. Overvoltage light will turn on and buzzer will sound continuously. Alarm and light shut off automatically when voltage goes below 245V.
  • Overheat protection: if sensor detects IGBT heat sink temperature is over 55⁰C, machine will shut down, overheat light will turn on and buzzer will sound continuously. Increase water pressure or lower water temperature until alarm goes off itself.
  • Overcurrent/malfunction protections: machine will shut down, indicator light will turn on and buzzer wil sound continuously if one of these situations occurs:
    • One of the machine parts becomes overheated.
    • Interfering signal detected.
    • Short circuit between work pieces and induction coils
    • Machine failures.
    • Induction coils touching each other.
    • The input voltage is too low.
    • Low water pressure protection: if water pressure goes below 29 PSI.

IMPORTANT!!

  • Always wear protective gear and goggles when operating the machine. Crucibles must be covered all the time during operation. Across International is not responsible for any injury or damage caused by misuse.
  • Do not run no-load operation for a long period of time, it might cause damage to the machine.
  • Circulating water must be pure, clean and below 45C.
  • Machine must be grounded properly all the time during operation.
  • Do NOT use single-turn coil if coil diameter is smaller than 4 inches, it will cause high frequency damage to the machine.
  • Thread tape (or related material) is absolutely prohibited during installation of induction coils.

Specifications

Specifications

 

 Max. input current  57 A (71A 3-phase circuit breaker required)
 Power  460 VAC 50/60Hz three phase (380V available upon request)
 Output frequency
 30-80 KHz
 Max. oscillating/input power  
 45 KW
 Duty cycle

 100%

 Heating timer
 1-99 seconds
 Dwelling timer  1-99 seconds
 Cooling timer  1-99 seconds
 Air cooling 
 Rear fan
 Water pressure
 ≥ 0.2 Mpa (29 PSI) you may use tap water
 and water pump (>1/4HP & >240 Gph)
 Water flow
 1.6 gallons (6 liters) per minute
 Induction coil
 See detail specs below, we will make coils
 according to your requirements
 Controller weight
 Unit: 110 Lb
 Heater weight
 Unit: 84 Lb
 Controller size
 25 x 12 x 21"
 Heater size
 20 x 11 x 16"
 Connection cables
 7 feet
 Remote foot switch
 7 feet
Standard Packages


Standard package

 

 Part description

Quantity

 Part image

 IH45AB power supply
1 set

 Connection cable (7 ft)
 1 set

 Foot switch (7 ft)
 1 pc

 2 Pin Cable 1 pc

 5 Pin Cable 1 pc

 Power Cable 1 pc

 Optional copper tubing induction coil made according to customer's requirements Upon request

 Stainless steel hose clamp
8 pcs

 Fuse 5 pcs

 Operation manual  1 pc

Overview

Note: This model only available in 460-480 volt three phase.

Across International IH series mid-frequency induction heaters are designed to operate between 30 and 80 kHz. Mid-frequency heaters are excellent for small parts heating, cutting, diamond tool brazing, soldering copper plumbing fittings, auto parts heat-treating, annealing of stainless steel containers and more.

Mid-frequency induction heaters are the simplest in terms of design and implementation. With their low cost of ownership and maintenance, they are the most popular and reliable machines. The 15kW models are especially popular for their large power capacity and small footprint at an affordable price. This makes them standard equipment for many factories, labs and workshops where 230V AC is available.

 

Safety Features

  • Overvoltage protection: machine shuts down when input voltage is over 245V. Overvoltage light will turn on and buzzer will sound continuously. Alarm and light shut off automatically when voltage goes below 245V.
  • Overheat protection: if sensor detects IGBT heat sink temperature is over 55⁰C, machine will shut down, overheat light will turn on and buzzer will sound continuously. Increase water pressure or lower water temperature until alarm goes off itself.
  • Overcurrent/malfunction protections: machine will shut down, indicator light will turn on and buzzer wil sound continuously if one of these situations occurs:
    • One of the machine parts becomes overheated.
    • Interfering signal detected.
    • Short circuit between work pieces and induction coils
    • Machine failures.
    • Induction coils touching each other.
    • The input voltage is too low.
    • Low water pressure protection: if water pressure goes below 29 PSI.

IMPORTANT!!

  • Always wear protective gear and goggles when operating the machine. Crucibles must be covered all the time during operation. Across International is not responsible for any injury or damage caused by misuse.
  • Do not run no-load operation for a long period of time, it might cause damage to the machine.
  • Circulating water must be pure, clean and below 45C.
  • Machine must be grounded properly all the time during operation.
  • Do NOT use single-turn coil if coil diameter is smaller than 4 inches, it will cause high frequency damage to the machine.
  • Thread tape (or related material) is absolutely prohibited during installation of induction coils.

Features
Across International IH45AB Induction Heater Features
  • Dual-station with connection cables and hose let you separate the heater and controller up to seven feet, allow you to stay away from high temperature, dirty and corrosive environment and for a safer operation, or if you need to move the heater to your work pieces constantly during operation.
  • Ease of use: just plug in the power and connect the water cooling system. Our simple instruction allows you to use the heater in 15 minutes.
  • Light weight, portable, instant heat and up to 90% energy savings.
  • Precise control with digital output, frequency and current displays.
  • Remote foot switch for safer operation.
  • Dual automatic and manual modes.
  • Optional graphite and silica crucibles available. (melting material decides crucible type, weight and size of the material decide crucible size)
  • Custom coil design (fixed coil or coil on a cable so it can be used by hand like a wand).
  • ISO 9001:2008 registered manufacturer.
  • We provide sample testing and custom made coils in our New Jersey facility.
Copyright © 2008-2023 Across International. All rights reserved.